FXR Division “Motorwitch” Handle Bars for Road Glide We worked Directly with one of the Industries Top Motor Builders to Design and Build a set of bars that would that give Him and You the Narrow Width (30.5” from end to end with a 12 Degree Wrist Angle which we have found the to be the closest to Natural Wrist Position) and Stance of a T Bar, allow for a Direct Mount to your Factory Riser WITHOUT any need for expensive Gauge and/or Handlebar Relocation Plates, give FULL visibility of your gauges and Media Center, and hold up to the rigors of his performance riding abilities as well as his Built 151 Leading Edge Performance Equipped Motor. Like our Split MX, Split Angle, and G Series Bars… we manufacture these IN HOUSE out of 1.250 X .125 steel tubing, we make sure to debur ALL material inside and out prior to welding for the smoothest wire pulls, and like ALL of our FXR Division Bars, are Throttle By Wire READY… YES… Your OEM Throttle By Wire fits PERFECTLY!! ALL FXR Division Handle Bars are finished in a High Quality Gloss Black Powder Coat (CHROME IS NOT AVAILABLE AS IT HAS BECOME TOO EXPENSIVE AND DIFFICULT TO QUALITY CONTROL…Our customers have been purchasing our FXR Division Bars and Crash bars in Black and having them stripped and plated locally to them) ***Bars pictured on BLACK Road Glide are 14” FXR Division Motorwitch Bars, Bars pictured on the RED Road Glide are 12”*** For 2013 and Earlier Road Glide Models You will need to Upgrade your Handlebar Clamp from the OEM 1” to a 1.25” Handlebar Clamp… sold on Our site. For 2015 to 2020 Road Glide Models: 12” OR 14” Motorwitch Bars DO NOT Require extending cables and/or lines… Your Stock Cables work just fine!!! 16” Bars DO require Extended Wiring and Hydraulic Clutch and Brake Lines. If you would like to replace your OEM or extend your Clutch and ABS Brake Line… Parts RECOMMENDED and we SELL to to do so are on our “Clutch Cables, Brake Lines, and Fittings” page: CAN BUS HANDLEBAR CONTROL WIRE EXTENSIONS (1) GUERRILA CABLES Plug N Play CAN bus Xtra Length 34” (42” for 16 inch bars) CLUTCH LINE (1) Universal Clutch Line Adapter (1) 70” Goodridge Clutch Line (71” for 16 inch Bars) (1) Straight Banjo Fitting for Hydraulic Clutch Master Cylinder TOP ABS BRAKE HOSE (1) Goodridge ABS Adapter Block (1) 60” Goodridge Brake Hose (1) Straight Banjo Fitting For Brake Master Cylinder 2021 and Later RG Models: You can run a 12” Motorwitch bar WITHOUT having to extend the OEM Clutch Cable, however you do need to do a little re-routing of the clutch cable… 14” Motorwitch Bars would require an +4 extended clutch cable… we use and sell the +4 FBInc Clutch Cable Extension and STRONGLY recommend the FBInc Clutch Adjuster as well… We also like to upgrade the Brake Line and Fitting at this time as well… you would need to purchase the ABS Adapter Block, a 60” Brake Hose, and a Straight Banjo Fitting… ALL Available on our site !!! For 16” Motorwitch would require a +6 FBInc Clutch Cable Extension, 60” Brake Hose, ABS Adapter, Straight Banjo Fitting and 42” Guerrilla Cables Extended CanBus Wiring Kit... ALL Available on our site !!! ** If your OEM Perch Clamp has a locating pin… it will be necessary to remove it before installation… Or you can purchased replace it with the smaller clamp, located on our site ** *** For BEST overall Feel and Performance… we HIGHLY RECOMMEND running a Solid Handlebar Grip such as the Performance Machine Renthal Grips on our site… Also, don't forget to get a set of NEW Gooden-Tite FLT Handlebar Bushings to go with your bars!*** ****We normally DO NOT stock bars over 16”… they are Made To Order and may take a little bit longer to manufacture and ship… Orders for Bars over 16” WILL BE subject to a 20% Cancellation Fee if order is cancelled after 7 Days from the Date the Order was placed*** We do our best to have ALL of Our FXR Division bars IN STOCK. However, our FXR Division Motorwitch Bars are in HIGH DEMAND and if they are not immediately available… then they are currently IN PRODUCTION. If do not receive a Shipping Notification, with your tracking number within 1-3 business days… Then please allow 2-4 weeks for orders to ship. ALL FXR DIVISION PARTS ARE PROUDLY MADE AND MANUFACTURED IN THE USA.

FXR Division HANDLE BARS FOR 2013 - EARLIER / 2015 -2023 ROAD GLIDE MODELS (Except 2023 CVO)

FXR DIVISION

$424.99 - $774.99
SKU:
FXRMWH
Availability:
Please allow up to 2-4 Weeks for shipping.
Adding to cart… The item has been added

FXR Division “Motorwitch” Handle Bars for Road Glide

We worked Directly with one of the Industries Top Motor Builders to Design and Build a set of bars that would that give Him and You the Narrow Width (30.5” from end to end with a 12 Degree Wrist Angle which we have found the to be the closest to Natural Wrist Position) and Stance of a T Bar, allow for a Direct Mount to your Factory Riser WITHOUT any need for expensive Gauge and/or Handlebar Relocation Plates, give FULL visibility of your gauges and Media Center, and hold up to the rigors of his performance riding abilities as well as his Built 151 Leading Edge Performance Equipped Motor.

Like our Split MX, Split Angle, and G Series Bars… we manufacture these IN HOUSE out of 1.250 X .125 steel tubing, we make sure to debur ALL material inside and out prior to welding for the smoothest wire pulls, and like ALL of our FXR Division Bars, are Throttle By Wire READY… YES… Your OEM Throttle By Wire fits PERFECTLY!!

ALL FXR Division Handle Bars are finished in a High Quality Gloss Black Powder Coat (CHROME IS NOT AVAILABLE AS IT HAS BECOME TOO EXPENSIVE AND DIFFICULT TO QUALITY CONTROL…Our customers have been purchasing our FXR Division Bars and Crash bars in Black and having them stripped and plated locally to them)

**** If your OEM Perch Clamp has a locating pin… it will be necessary to remove it before installation… **

****We normally DO NOT stock bars over 16”… they are Made To Order and may take a little bit longer to manufacture and ship… Orders for Bars over 16” WILL BE subject to a 20% Cancellation Fee if order is cancelled after 7 Days from the Date the Order was placed***

****We do our best to have ALL of Our FXR Division bars IN STOCK. However, our FXR Division Motorwitch Bars are in HIGH DEMAND and if they are not immediately available… then they are currently IN PRODUCTION.

If do not receive a Shipping Notification, with your tracking number within 1-3 business days… Then please allow 2-4 weeks for orders to ship.

ALL FXR DIVISION PARTS ARE PROUDLY MADE AND MANUFACTURED IN THE USA.

Shop with V-Twin Now. Free Shipping on orders $250 and over (exclusions apply). Our team has over 50 years of combined V-Twin experience and is ready to assist you in finding the right parts and accessories for your job.

You Might Be Interested in These

Customers who bought this product, are usually these related products.